NiceAft wrote: ↑Tue Jun 10, 2025 5:48 am Shane Anthony,

I too could not find the article you mentioned, but i did find this from BWY. https://www.bwyachts.com/rig_tuning_tips.htm

Todd is quite an authority on all Macs.

Thank You so much

Hi everyone, I’m trying to adjust the stays and came across this post about bruce whitmore's article about the rig trim basics. The person had said you can find it in “featured articles” but I can’t find out how to select that. Any help would be much appreciated

Shane anthony said: Thanks for the info, I think I’m understanding the special mount. One way to do it would basically be to turn a small section of the rounded corner of the boat to a 90° corner with a couple SS steel plates welded at a tapered 90° then bolt one side to the stern and the other to ...

WinSome wrote: ↑Tue Apr 01, 2025 5:24 am FYI suggestion. Replace the plywood spacers you refer to with $ store cutting boards. It’s inexpensive, and won’t rot, and can be cut, molded and might not even need painting.

Sorry, I wasn’t very clear about it. I was just going to use the plywood for making a template.

I believe the most difficult part of mounting an auxiliary outboard on an :macm: is the limited flat surface on the stern, allowing clearance for the rudders.. Highlander made a special mount which curved around the starboard side. I don’t have any photos. Maybe he see’s this post and adds his unde...

I believe the most difficult part of mounting an auxiliary outboard on an :macm: is the limited flat surface on the stern, allowing clearance for the rudders.. Highlander made a special mount which curved around the starboard side. I don’t have any photos. Maybe he see’s this post and adds his unde...

I believe the most difficult part of mounting an auxiliary outboard on an :macm: is the limited flat surface on the stern, allowing clearance for the rudders.. Highlander made a special mount which curved around the starboard side. I don’t have any photos. Maybe he see’s this post and adds his unde...

IMG_2700.png Was thinking something like this might be an answer to auxiliary power if the main would go down. The smaller tube shape of the shaft might fit between the main and rudder without interfering with movement. I haven’t measured anything but was thinking mounting it would be simple compar...

Sure, thanks for the replies. Sounds like if I use loctite, ring dings, cotter keys seizing wire and left and right threaded nuts I should be fine :D seriously though thanks. Here's a link to a PPT that I made trying to document the assembly of the CDI furler: https://1drv.ms/p/s!Ag0w1ybOLvphkuk4dK...

Hi, would that be two nuts per thread for a total of 4? I’d have to order left handed nuts to do it. Thanks for the reply Ah...right. The turnbuckle has left handed nuts. I don't have a turnbuckle. So disregard my comments. I have the threaded piece from the headstay that attaches to the fuller. If...

Okay I think I understand now Thank you! Does this look correct? If I recall, mine has nuts (x2) on the threads to prevent the stay from moving. I think those ring dings would do it. Hard to tell from the pic Hi, would that be two nuts per thread for a total of 4? I’d have to order left handed nuts...

Hi everyone, it’s probably my lack of knowledge but can anyone tell me how to secure the forestry turnbuckle? I was under the impression that after securing it you’d want it to still be able to spin freely? I’m thinking for the ability to adjust it without having to remove anything you’ve put to se...

Do you have a furling jib or a hank on jib. Firstly, once you get your rigging tuned, it should be set and forget. I've NEVER adjusted my rigging after I got it adjusted. I simply unpin and re-pin the forestay when raising the mast. The turnbuckle (if you don't have a fuller) should be pinned with ...

Hi everyone, it’s probably my lack of knowledge but can anyone tell me how to secure the forestry turnbuckle? I was under the impression that after securing it you’d want it to still be able to spin freely? I’m thinking for the ability to adjust it without having to remove anything you’ve put to sec...

Congrats on getting her rigged. I'm not familiar with that furler style. Does the metal outside rotate? It looks okay to me. It appears the furler metal shell has some scratches from previous abrasions with the anchor. Unless the anchor is preventing it from rotating, I wouldn't worry about it. It ...