Search found 5213 matches

by kmclemore
Wed Mar 27, 2024 10:22 am
Forum: Repairs and Modifications
Topic: Hatch vent options
Replies: 6
Views: 136

Re: Hatch vent options

Interesting design. I note that it's threaded, with what appears to be a lock-nut collar? Threads can sometimes be a bear to 3D print. Also, I note there's no dorade box or way to drain off incoming water, in the event of operation during inclement weather. Would you just remove it and plug the hole...
by kmclemore
Mon Mar 25, 2024 10:01 am
Forum: MacGregor Powersailor Discussion
Topic: Service suggestions
Replies: 8
Views: 353

Re: Service suggestions

Macsailing wrote: Mon Mar 25, 2024 9:15 am Anybody find an easy way to lubricate steering gear and cable?
I don’t believe every steering cable has Zirk fittings, but if yours does, that’s the best way. If not, you may be able to do so from inside the helm by removing the cover.
by kmclemore
Mon Mar 25, 2024 9:57 am
Forum: MacGregor/Venture Discussion
Topic: Stupid Question 1:Fuse Replacement
Replies: 6
Views: 214

Re: Stupid Question 1:Fuse Replacement

I don’t have a fuse panel in nearby to take a picture for you, but if you look closely around the bottom edge of the fuse holder, you’ll find a small hole. Gently push a paperclip or similar small metal item into that hole and the red cover for the fuse will pop out. Careful, as it is spring loaded....
by kmclemore
Fri Mar 22, 2024 6:22 pm
Forum: Destinations, Clubs, Events and Venues
Topic: Annapolis Sailboat show April 26-28, 2024 Anyone else going?
Replies: 3
Views: 153

Re: Annapolis Sailboat show April 26-28, 2024 Anyone else going?

Yeah, I saw that and wanted to go…. Until I realized Jan and I were scheduled to be on a camping trip with our Scouts. ¯\_(ツ)_/¯
by kmclemore
Mon Mar 18, 2024 8:32 am
Forum: MacGregor Powersailor Discussion
Topic: Those with Facebook…
Replies: 7
Views: 277

Re: Those with Facebook…

Not sure why you're getting that, Ray - I just checked it again and it's still there. Are you a FB user? As for what it was, it was a video of a Mac passing by a marina, at full blast, so it was planing and moving along nicely. The issue was the negative comments about Macs... lots of comments about...
by kmclemore
Mon Mar 18, 2024 5:23 am
Forum: MacGregor Powersailor Discussion
Topic: Those with Facebook…
Replies: 7
Views: 277

Those with Facebook…

Saw this today… join in and defend the faith!

https://www.facebook.com/share/r/V1sKUj ... tid=lfGLxo
by kmclemore
Fri Mar 15, 2024 3:22 pm
Forum: MacGregor Powersailor Discussion
Topic: premade 26X cushion covers
Replies: 29
Views: 7020

Re: premade 26X cushion covers

Anyway, the reason for the post is things have gotten slow at work (my day job) so am offering other Mac 26X owners replacement cushions. I can also do 26M owners cushion replacements as a neighbor owns this boat and would be able to get the pattern for these cushions as well. Unlike others, I can ...
by kmclemore
Wed Mar 13, 2024 9:33 pm
Forum: MacGregor Powersailor Discussion
Topic: Service suggestions
Replies: 8
Views: 353

Re: Service suggestions

Also..maybe grease the motor pivot points and tilt. Yep - that's important. Grease all the available zirk fittings, and apply a small amount of engine oil on any moving joints that aren't greased. You could check the tilt fluid to ensure it's properly topped up. Generally this isn't a problem, but ...
by kmclemore
Wed Mar 13, 2024 8:42 pm
Forum: Repairs and Modifications
Topic: Almost ready to float
Replies: 12
Views: 302

Re: Almost ready to float

Yeah, I'm with Russ. Never, never NEVER have a quick release or push-to-release pin on ANY important rigging , and this particular point of rigging is the most important of all. If that link gives way unexpectedly, people can be very seriously injured or potentially die... and your boat will be seri...
by kmclemore
Tue Mar 12, 2024 6:40 pm
Forum: MacGregor Powersailor Discussion
Topic: Service suggestions
Replies: 8
Views: 353

Re: Service suggestions

Lubricate the steering gear/cables

When is the last time you serviced the cooling impeller? If it's over 5 years, I'd replace it.
by kmclemore
Wed Mar 06, 2024 9:45 am
Forum: Trailers & Towing
Topic: Waxing a Trailer
Replies: 7
Views: 2286

Re: Waxing a Trailer

Well, wax repels water, and water creates rust, so, yeah, waxing could theoretically prevent rust on a trailer. However, the really serious rust on our trailers occurs where you can't wax... inside the tongue, where it joins the 'Y' section going back to the axle. So... a waxed trailer could potenti...
by kmclemore
Sun Mar 03, 2024 4:44 pm
Forum: Repairs and Modifications
Topic: Poked a hole in muh boat.
Replies: 3
Views: 511

Re: Poked a hole in muh boat.

Looks like there was a bubble between the gel coat and the polyester. It’s a common manufacturing defect in fiberglass products. In which case, it’s not a leak issue. I would simply get some Marine-Tex, fill the void with it, and apply masking tape over it to give you a smooth finish. When it harden...
by kmclemore
Tue Feb 27, 2024 10:50 am
Forum: Trailers & Towing
Topic: 26X Trailer Repair
Replies: 6
Views: 254

Re: 26X Trailer Repair

I also suggest Tractor Supply. They have a surprisingly good selection of trailer parts and supplies. Take your old U-bolt with you to ensure a good fit.

(I should note that for some reason I can’t say “u-bolt” without wanting to call it “das bolt”. :D )
by kmclemore
Thu Feb 22, 2024 11:31 am
Forum: MacGregor Powersailor Discussion
Topic: Opinions on Tohatsu Motors
Replies: 6
Views: 361

Re: Opinions on Tohatsu Motors

Similar discussion over here.... https://www.macgregorsailors.com/forum/viewtopic.php?p=367630#p367630 I recommend reading it, as it's recent information and has some good suggestions. In March I will be picking up my 26X with a shiny new Suzuki DF60AV four-stroke in place of my old Tohatsu 50D two-...
by kmclemore
Tue Feb 20, 2024 5:52 pm
Forum: Repairs and Modifications
Topic: Old geezer stanchion mod
Replies: 23
Views: 1394

Re: Old geezer stanchion mod

For those considering getting into 3D printing, beware. If you are inclined to go down the rabbit hole when it comes to projects, this is an enabling device. I mean, for Pete's sake, as I write this I am printing a snap-on lid for an odd-sized can of tomato paste. It's a great tool, but also a grea...