hauling with mast stepped but lowered

A forum for discussing topics relating to MacGregor Powersailor Sailboats
User avatar
Tomfoolery
Admiral
Posts: 6135
Joined: Tue Jul 05, 2011 7:42 am
Sailboat: MacGregor 26X
Location: Rochester, NY '99X BF50 'Tomfoolery'

Re: hauling with mast stepped but lowered

Post by Tomfoolery »

Jimmyt wrote: Fri Sep 17, 2021 2:45 pm Highlander tells it like he sees it. I like that. You never have to ask him "what's you honest opinion", cause that's all you're gonna get. And usually both barrels. :D Love that whacky guy.
He’s also one of the most interesting people you’ll ever meet. I’ve had the pleasure of sailing and hanging out with him and a few others from this board up in the Toronto area for a few years (the MMOR rendezvous), though he’s waaaay over on the left coast as of a couple of years ago. 8)
Tom
Be seeing you . . .
leefrankpierce
Engineer
Posts: 136
Joined: Fri Oct 06, 2017 5:13 am
Sailboat: MacGregor 26X
Location: Dallas Ft-Worth Texas

Re: hauling with mast stepped but lowered

Post by leefrankpierce »

Seems there is a story on the forum about someone having portlights in the side and sinking their boat when one opened, presumably when heeled far to that side.I always wondered how close to the water we get our rub-rails.

Worried about the mast mounting point, it is not designed to resist up pressures.

I can imagine someone in a Cabover not seeing the mast and getting the mast through the windshield.

Pulling with a Mini-Van?
My 4-WD 1500 suburban has a hard enough time keeping the rig under control, never bought into the adds using a car to tow.
I do like the 2 axle trailer, possibly that helps enough.
26X in Dallas Fort-Worth area Texas
Slip at Eagle Mountain Lake
:macx:
User avatar
Ixneigh
Admiral
Posts: 2225
Joined: Thu Sep 09, 2010 11:00 am
Sailboat: MacGregor 26M
Location: Key largo Florida

Re: hauling with mast stepped but lowered

Post by Ixneigh »

Concur with others this is a bad idea, although comforting to know that the mast base is far more robust that I gave it credit for

Ix
"Shoal Idea"
2011 M, white
Etec 60
South Fl.
User avatar
PhysicsTeacher
Deckhand
Posts: 38
Joined: Fri Sep 02, 2016 6:09 pm
Sailboat: MacGregor 26X
Location: Abbotsford, BC, Canada 1999 26X, 60 HP Yamaha

Re: hauling with mast stepped but lowered

Post by PhysicsTeacher »

A few years ago I was at Harrison Lake (in British Columbia) getting ready to rig my :macx: . Suddenly a vehicle towing an :macx: pulled up next to me with his mast in the same position as the original poster mentioned.
The owner lived about 2 blocks from the boat ramp, and always trailered his boat that way. In addition, he had a back injury, so he was unable to raise the mast. Instead, he had an electric winch on his trailer. He attached the winch to the mast in the same location as the mast-raising system, hopped back onto the ground, and . . . bbzzzppt, up rose the mast, perfectly in place. He pinned his furler to the foredeck, and drove down the ramp to launch, about 10 minutes after his arrival.

I have to admit, his setup was pretty slick. :)

Kelvin

Bonus: I got into the water around 45 minutes later, and then I caught up to him on the lake. He was having motor issues and could only go in reverse. So, after all that, I reached our destination about 30 minutes before he did. 8)
No trees were killed to send this message, but a large number of electrons were terribly inconvenienced.
DaveC426913
Admiral
Posts: 1783
Joined: Mon Jul 14, 2008 8:05 am
Sailboat: MacGregor 26X
Location: Toronto Canada
Contact:

Re: hauling with mast stepped but lowered

Post by DaveC426913 »

PhysicsTeacher wrote: Wed Feb 08, 2023 8:13 pm The owner lived about 2 blocks from the boat ramp,
In my case, it was a very built up area in megacity Toronto. Nevermind the risk to the mast - I can't see how this guy even cornered without taking out a condo or two.

Oh. Did I forget to mention that the whole neighborhood is laced with high voltage overhead streetcar power lines?
Screenshot 2023-02-09 222511.png
You do not have the required permissions to view the files attached to this post.
MacX 2000 Honda BF50A 'SeaSaw'
Post Reply